JEFFCO 3122-DGel
1:1 CLEAR GEL HARDENER
Back to
Hardener page
Product Description:
Thixotropic, gel version of 3122-D hardener. Medium pot life and good clarity for vertically applied epoxy coatings. Highly resistant to amine blush. Easy to use 1:1 volumetric mix ratio. No VOC’s, 100% solids. Low odor during cure.
Product Uses:
Clear vertically applied coatings, quartz or aggregate broadcasts onto vertical surfaces. Used where a high build on vertical walls is desired. Generally used with either Jeffco 1301, 1303 or 9211.5 epoxy resins.
TIPS:
Resin and hardener should be between 70° F and 80° F for best results. Mix equal parts (by volume) of the resin and hardener slowly and carefully for 2-3 minutes, trying not to "whip" in excessive air. Once the material is mixed, it is typically applied by roller to the wall and allowed to cure. Once rolled, it may also be broadcast with quartz or other suitable media. The convenient gel consistency finds use in many other applications where a thixotropic, high build system is desired. |
| PROPERTIES OF 3122-DGel HARDENER (neat): |
Minimum |
Maximum |
| Gel Time: Gel Time (minutes@ 77°F, 150 grams)
|
30
|
35
|
| Viscosity: @ 77°F, cps
|
Thixotropic |
Thixotropic
|
|
Color: (Gardener)
|
|
|
Weight Per Gallon: (lbs.)
|
8.2
|
8.2
|
|
Weight Per Active H:
|
|
|
|
Mix Ratio: (1:1 volume)
|
|
|
|
Thin Film Cure Time: (minutes @ 175°F)
|
|
|
|
Thin Film Set Time: @ 77°F (hours)
|
|
|
|
Cure Time: @ 75°F (hours)
|
|
|
|
Pot Life: (minutes @ 77°F, 150 grams)
|
|
|
|
| TYPICAL CURED PROPERTIES WITH 1301 RESIN |
Minimum |
Maximum |
|
Mixed Viscosity, cps: Thixotropic |
|
HDT: (°F) ASTM D648-264
|
|
|
|
Shore D Hardness:
|
78 |
78 |
|
Barcol Hardness Units :
|
|
|
|
Flexural Strength: (psi)
|
|
|
|
Flexural Modulus: (psi)
|
|
|
|
Tensile Strength: (psi)
|
|
|
|
Tensile Modulus: (psi)
|
|
|
|
Elongation: %
|
7.5 |
7.5 |
|
Compressive Strength: (psi)
|
|
|
|
Bond Strength: psi ASTM C882
|
|
|
|
Water Absorption: %
|
|
|
|
Heat Deflection Temperature:
|
|
|
|
Heat Distortion Temperature: °C
|
|
|
|
Service Temperature: °F
|
|
|
|
Tensile Strain at Break: %
|
|
|
|
How Supplied:
Pails, Drums
Back to
Hardener page
The information contained herein is offered without charge
for use by technically qualified personnel at their discretion and risk.
All statements, technical information and recommendations contained herein
are based on test and data which we believe to be reliable, but the accuracy
or completeness thereof is not guaranteed and no warranty of any kind
is made with respect thereto. Always read, understand, and comply with
hazard warnings described in the products' Material Safety Data Sheet(s)
before use.
|
