JEFFCO 6004-LV
ANHYDRIDE CURING AGENT
Back to
Hardener page
Product Description:
Proprietary anhydride hardener. High strength, medium pot life, lower viscosity, faster curing and improved clarity versus competitive anhydride hardeners. Jeffco 6004LV’s low viscosity gives a significantly lower mixed viscosity with standard epoxy resins, which can improve many processes previously requiring a heated resin system. Jeffco 6004LV’s proprietary formula has a higher Tg than standard competitive anhydrides, typically resulting in a 10°C improvement in Tg. Even though it has a standard pot life at 85°C, it cures faster at standard anhydride cure temperatures. Jeffco 6004LV is extremely clear, with a Gardner color of <1 for cosmetically better parts compared with competitive anhydride curatives. No solvents, 100% solids. Complies with FDA 175.300. Ships DOT non-regulated.
Product Uses:
Filament winding and other large heat-cured parts. |
| PROPERTIES OF 6004-LV HARDENER (neat): |
Minimum |
Maximum |
| Gel Time: (minutes @ 185° F, 100 grams)
|
27
|
34
|
| Viscosity: @ 77°F, cps
|
80
|
150
|
|
Color: (Gardener)
|
1 (max) |
|
Weight Per Gallon: (lbs.)
|
9.9 |
10.2 |
|
Weight Per Active H:
|
|
|
|
Mix Ratio: Parts Per 100 Resin (by weight, 1:1 volume)
|
90 |
90 |
|
Thin Film Cure Time: (minutes @ 175°F)
|
|
|
|
Thin Film Set Time: @ 77°F (hours)
|
|
|
|
Cure Time: @ 75°F (hours)
|
|
|
|
Pot Life: (minutes @ 77°F, 75 grams)
|
|
|
|
TYPICAL CURED PROPERTIES WITH 1301 RESIN
|
Minimum |
Maximum |
|
Cure schedule: Initial cure of 2 hours @ 185° F + post cure
of 3 hours @ 302° F |
|
HDT: (°F) ASTM D648-264
|
|
|
|
Shore D Hardness:
|
|
|
|
Barcol Hardness Units :
|
|
|
|
Flexural Strength: (psi)
|
20,300 |
20,300 |
|
Flexural Modulus: (psi)
(x 10 to the 5th power) |
495 |
495 |
|
Tensile Strength: (psi)
|
12,900 |
12,900 |
|
Tensile Modulus: (psi)
(x 10 to the 5th power) |
465 |
465 |
|
Elongation: %
|
5.1 |
5.1 |
|
Compressive Strength: (psi)
|
18,800 |
18,800 |
|
Bond Strength: psi ASTM C882
|
|
|
|
Water Absorption: %
|
|
|
|
Heat Deflection Temperature:
|
|
|
|
Heat Distortion Temperature: °C
|
|
|
|
Service Temperature: °F
|
|
|
|
Tensile Strain at Break: %
|
|
|
|
How Supplied:
Pails, Drums, Tote Bin
Back to
Hardener page
The information contained herein is offered without charge
for use by technically qualified personnel at their discretion and risk.
All statements, technical information and recommendations contained herein
are based on test and data which we believe to be reliable, but the accuracy
or completeness thereof is not guaranteed and no warranty of any kind
is made with respect thereto. Always read, understand, and comply with
hazard warnings described in the products' Material Safety Data Sheet(s)
before use.
|
